The radar presence detection provides automatic disconnection of the truck on leaving and thus also on energy saving. It is used when the vehicle itself does not have any detection sensors (e.g. seat contact switch) or an intervention in the vehicle electronics is not wanted. With this presence detection, also usage hours can be displayed. The plug and play setup only takes a few minutes.
Crash Sensor Remote
The patented digital Crash Sensor Remote is unique worldwide. The dual system has a three-axis acceleration sensor and an impact sound microphone. Its settings are determined by a “learning trip” during operation and defined in three “crash stages” in the Mobile Easykey software. Scheduled actions are defined for each level. Thus, e.g. level one is only documented in the logbook, an e-mail is sent to the safety officer at level two, and at stage three the vehicle is stopped or slowed down in speed. The sensor is already included in the modules fleet and crash+remote.
With the Departure Control, drivers can record the condition of the truck in the logbook of the Mobile Easykey software, before starting the journey by pushing a green or red button.
The Event Tool can be used to record usage hours and two other events in the logbook of the Mobile Easykey software. Channel 1 is used to record the hours of use of the vehicle. These entries appear automatically every 15 minutes in the logbook and record the period of use in a 15-minute period. The data can be used to get detailed evaluations of the actual use of the vehicles.
Channels 2 and 3 can be freely assigned with a switching signal. For example, the recording of journeys with and without load (corresponding sensor necessary) or warnings of the vehicle. These data also appear in the logbook and can be used for reports and statistics.
For efficient use of the Event Tool, the software module Maintenance, UVV and Mail supplements the Mobile Easykey Software.
EBZ Power Sensor
The EBZ Power Sensor generates log entries for usage hours for electric vehicles. These entries appear automatically every 15 minutes in the logbook and record the period of use in a 15-minute period. The data can be used to get detailed evaluations of the actual use of the vehicles.
For efficient use of the EBZ Power Sensor, the software module Maintenance, UVV and Mail supplements the Mobile Easykey Software.
Passive transponders provide users with access to forklifts and all other equipped machinery, if they have the permission to use. We have different colors and styles on offer. The transponder is also available in a special EX protection version.
We guarantee for our transponders that each ID has only been assigned once and the activation of the module also takes place at a distance of up to 3 cm.
With the Universal Card Reader, we support the following variants:
- EM4100/4102/4200 (Unique – Standard Mobile Easykey Transponder)
- EM4150, EM4450
- HITAG 1
- HITAG 2
- HITAG S
- HID Proximity
- MIFARE Classic
- MIFARE DESFire
- LEGIC prime
- LEGIC advant
- HID iCLASS
The supported variants are constantly being expanded. On our own test bench, we check the customer’s transponder for compatibility.
EKZ 020… Retractable Transponder Holder
This functional coil is used for the practical attachment of the transponder “to a person”.The coil can be pulled out up to approx. 70 cm and automatically carries the transponder back safely. This tool is available in different colors. Lost transponders are now a thing of the past.
RFID Desktop Readers
EKZ-006 Mobile Easykey Desktop Reader
The Easykey transponders (EM4100 / 4102 / 4200) can be easily assigned to the various users or batteries via this Desktop Reader. The Mobile Easykey software contains all necessary drivers and functions. The Desktop Reader can also be used as an additional authentication point for logging on to the software.
EKZ-007 Universal Desktop Reader
Via the Universal Desktop Reader all common (125 kHz and 13.56 MHz) transponders can be conveniently assigned to the various users or batteries. The Mobile Easykey software contains all necessary drivers and functions. The Universal Desktop Reader can also be used as an additional authentication point for logging on to the software.
Mounting: Universal Holder for modular
The universally applicable bracket can be fitted to the A-pillars or spars of all standard forklifts. The Universal Holder is securely fastened and can be adjusted for optimum operability. Several joints enable ergonomic positioning. The Universal Holder can be used for all modular modules. For some vehicles an additional special “fixing claw” of the manufacturer is required for the Apillar!
When no attachment claw is available or can not be used, we have developed a special Fixing Plate. The Universal Holder is attached to it.
Mounting: Universal Holder for modular and fleet
Universalhalter with adhesive foil
EKZ-077KL (for modular and fleet)
Never drill again! On vehicle and module side, the attachment is done with adhesive pads.
Universal Holder with M8 thread
EKZ-077M8 (for modular and fleet)
If it is not possible to attach the adhesive pad on the vehicle side, the attachment can be made with an M8 thread. On the module side, the attachment is made with an adhesive pad.
Mounting: Base Plate Crash Sensor
EKZ-075 Base Plate Crash Sensor Remote
For the safe and easy assembly we offer a Base Plate. This can also be installed in advance, so the subsequent assembly runs significantly faster.
Send us an eMail
Thanks for your message. It will be forwarded to Sven Dreilich, Christoph Weinzettel or Norman Seib.